陰極保護設計基本要求 Basic requirements for cathodic protection design

時間：2022-09-09作者：焦作市虹泰防腐材料有限公司瀏覽：86

陰極保護設計基本要求

(1)電連續性：被保護結構必須電氣導通。焊接管道沒有電連續問題，但對于承插口連接的管道，管段之間要進行跨接。

(2)電氣絕緣：被保護結構必須與其他埋地設施或接地系統電絕緣。絕緣接頭盡量地上安裝。設置管道絕緣位置時，要充分認識到以下兩點:

①陰極保護電流可能會引起絕緣接頭非保護側腐蝕。管道內部有積液時，絕緣接頭要安裝在高處或豎直安裝，避免內部積液。

②有絕緣就要有防雷保護。例如閥室內部接地網通常與主閥隔離，如果對電氣隔離不進行保護，往往會導致絕緣墊或絕緣卡箍被擊穿。

(3)站場接地：工藝管道可以通過避雷器與接地網連接。同部接地較可以使用鍵鋅材料，但有可能影響陰極保護系統工作。

(4)電屏蔽：聚乙烯膠帶防腐層、熱縮套及泡沫保溫層可能會導致陰極保護無效。

(5)混凝土加重層：沼澤、水網地帶的管道混凝土加重層要避免鋼筋與管道接觸。

(6)鋼套管穿越：避免主、套管短路，套管有高質量涂層時,兩端預留一段裸管。

(7)交流排流：**利用站場、閥室接地較以及穿路鋼套管進行排流，排流不夠時，安裝額外接地較，接地較與管道之間安裝通交隔直裝置。

（8）并行管道:避免管道與地床之間的干擾或管道之間的屏蔽問題，必要時聯合保護(涂層差異大時難以實現)。當無法避免陽極地床對相鄰管道的陽極干擾時，要加強受干擾管道的防腐層。

（9）如果定向鉆穿越段管道防腐層損壞嚴重，盡量不要采取回拖再鉆的方式?？梢酝ㄟ^(guò)加強局部陰極保護，如埋設犧牲陽極或增加陰極保護站的方式保護穿越段管道。

Basic requirements for cathodic protection design
1.  Electrical continuity: the protected structure must be electrically conductive. There is no electrical continuity problem for welded pipes, but for pipes connected by sockets, the pipe sections should be bridged.
2.  Electrical insulation: the protected structure must be electrically insulated from other buried facilities or grounding systems. Insulated joints shall be installed on the ground as far as possible. When setting the pipeline insulation position, the following two points shall be fully recognized:
（1） Cathodic protection current may cause corrosion on the unprotected side of insulated joints. When there is liquid accumulation inside the pipeline, the insulation joint shall be installed at a high place or vertically to avoid liquid accumulation inside.
（2） If there is insulation, there must be lightning protection. For example, the grounding grid inside the valve chamber is usually isolated from the main valve. If the electrical isolation is not protected, the insulation pad or insulation clamp will be broken down.
（3） Station grounding: the process pipeline can be connected to the grounding grid through lightning arrester. The bonding zinc material can be used for the same grounding electrode, but it may affect the operation of the cathodic protection system.
（4） Electric shielding: polyethylene tape anticorrosive coating, heat shrinkable sleeve and foam insulation layer may lead to ineffective cathodic protection.
（5） Concrete weighting layer: the pipeline concrete weighting layer in swamp and water network areas shall avoid the contact between reinforcement and pipeline.
（6） Steel casing crossing: to avoid short circuit between main casing and casing. When the casing has high-quality coating, a section of bare pipe shall be reserved at both ends.
（7） AC drainage: the grounding electrode of the station and valve chamber and the steel sleeve through the pipeline shall be used for drainage preferentially. If the drainage is not enough, an additional grounding electrode shall be installed, and a communication and straight separation device shall be installed between the grounding electrode and the pipeline.
（8） Parallel pipeline: avoid interference between pipeline and ground bed or shielding between pipelines, and conduct joint protection when necessary (difficult to achieve when coating difference is large). When it is impossible to avoid the anode interference of the anode ground bed to the adjacent pipeline, the anti-corrosion coating of the disturbed pipeline shall be strengthened.
（9） If the anti-corrosion coating of the pipeline at the crossing section of directional drilling is seriously damaged, try not to drag back and drill again. Local cathodic protection can be strengthened, such as burying sacrificial anodes or adding cathodic protection stations to protect the crossing pipeline.




焦作市虹泰防腐材料有限公司專注于恒電位儀,智能測試樁,深井陽極,帶狀鎂陽極,帶狀鋅陽極,鋁合金犧牲陽極,鎂合金犧牲陽極,鋅合金犧牲陽極等

• 詞條

  詞條說明

• 測試樁 犧牲陽極 管道電位陰極保護 檢測常用測試樁

  測試裝的用途主要用于陰極保護參數的檢測，是管道管理維護中**的裝置，按測試功能沿線布設。測試樁可用于管道電位、電流、絕緣性能的測試，也可用于覆蓋層檢漏及交直流干擾的測試。測試樁是一種專門用于管道陰極保護配以電位測試探頭對保護管道進行測試的附屬設備。測試樁的功能分類電位測試樁：主要用于檢測保護電位。犧牲陽極測試樁：用于連接犧牲陽極,測量犧牲陽極的性能參數。電流測試樁:測量管中電流。保護效果測試樁

• 帶狀鋅陽極注意事項及使用說明

  帶狀鋅陽極注意事項及使用說明?一、因純鋅金屬較脆，裝卸過程請勿暴力裝卸。二、因純鋅金屬較脆，氣溫較低狀態下應加熱增加其柔韌性，使用燃?xì)鈬姛艋蛘咂渌募訜峁ぞ甙唁\帶整卷均勻加熱到60-100度左右，人工摸起來燙手就可以。三、加熱到溫度后可以進行開卷作業，開卷不宜速度太快，應緩慢開卷；開卷不宜弄得太直；開卷過程中請勿反復折彎鋅帶，應避免突然彎曲和過度彎曲。四、如開卷過程中降溫太快，應開卷過程

• 固態去耦合器的工作原理及安裝

  要說固態去耦合器，可能很多人都不是很清楚具體用途。實際上固態去耦合器常用在管道陰極保護上，一般是用來延長管道的使用壽命。在管道的具體使用中有可能會發生一些故障，或者是惡劣天氣會影響使用壽命，這就要用到固態去耦合器。固態去耦合器的主要作用是起保護作用，也就是對管道陰極進行保護，減少電路故障，延長使用壽命。因?yàn)楣艿赖年帢O保護系統存在著一些弊端，也就是電磁干擾多，也是耦合器的雜散電流多。這些雜散電流在日

• 陰極保護中腐蝕的定義和發生

  陰極保護中腐蝕的定義和發生一、腐蝕的定義?腐蝕是物質與環境發生反應，劣化變質的過程。腐蝕如此普遍，以至于人們對其發生和發展熟視無睹，習以為常。二、腐蝕的發生?腐蝕是如何發生的呢?為什么一根完好的鋼管埋入土壤中，幾年后就會銹跡斑斑甚至穿孔報廢?要回答這些問題，要從金屬的前生后世來解釋。以碳鋼為例，它們?cè)谧匀唤缰惺且澡F礦石的形態存在的。在人類把鐵礦石轉換成鐵金屬的過程中，施加了大量