Configuring Timer DQ operating mode

時間：2021-07-28作者：上海騰希電氣技術有限公司瀏覽：93

Configuring Timer DQ operating mode



Timer DQ

Timer DQ operating mode allows you to output up to two edges per application cycle (for example OB 91, OB 6x) at a specific time, for example, for use as a cam output.

Select the Timer DQ operating mode for the required channel.


圖片: Mode of operation: Timer DQ

Inversion

You can invert the 24 V ** to adjust it to your process. By default, the ** is not inverted.

High-speed output

If you select the high-speed output option, the digital output is switched alternately to 24 V DC and ground.

Advantages of the high-speed output:

Extremely steep edges (output delay in the 1 μs range)

Extremely high switching frequencies

Maximum switching precision, for example, for use as a cam output

Assigning the output cam technology object

The output cam technology object must always be assigned to another technology object whose position is evaluated.

You can assign the output cam technology object to the following technology objects:

Synchronous axis

Positioning axis

External encoder

You can assign exactly one axis or one external encoder to the output cam.

You can assign multiple output cams to one axis or one external encoder.

Configuring the output cam technology object

Select the configuration of the output cam in the Technology objects folder in the project tree.

Configure the basic properties of the technology object in the Basic parameters configuration window.


圖片: Basic parameters

Name

Define the name of the output cam in this field. The technology object is listed under this name in the project tree. The tags of the output cam can be used in the user program under this name.

Assigned axis or external encoder

STEP 7 displays the axis or external encoder assigned to the output cam. You can use the link to directly access the basic parameters of the higher-level technology object.

Output cam type

Select an output cam type on the basis of the required switching behavior:

Position-based cam (position-dependent switch-on/switch-off)

Time-based cam (position-dependent switch-on and position-independent or time-dependent switch-off)

Output cam reference

In this selection, configure whether the switching points of the output cams are to reference the actual position or the position setpoint.

Unit of measurement

The unit of measurement shown for the position of the output cam corresponds to the unit of measurement of the higher-level technology object.

When a time-based cam is selected as the output cam type, the unit of measurement for the switch-on duration and other times is also indicated. The unit of measurement for output cams is always ms.

Hardware interface

Select the type of cam output in the Hardware interface configuration window.


圖片: Hardware interface

Select whether you want to output the switching **s generated at the digital output.

Activate output

Select one of the following two output options for outputting the cam track:

- Output via Timer DQ

For output by Timer DQ, select a cam output in the Output field. The selection box displays all channels that have been configured correctly.

提示 Extending the configuration limits A maximum of eight timer DQ can be configured at the X142 interface. If the Timer DQ at X142 are not sufficient for your needs, you can increase the configuration limits with time-based IO modules: - ET 200SP distributed I/O system: TM Timer DIDQ 10x24V - ET 200MP distributed I/O system: TM Timer DIDQ 16x24V You can find more information on these systems in .




提示 Unsupported instructions for the X142 interface The function blocks for the use of time-based IO (TIO instructions) are not supported by the X142 interface. Recommendation: For the timer DQ, use the output cam or cam track technology object.




- Output by digital output module

For output by a digital output module, select a digital output in the Output field. Only the digital outputs with previously defined PLC tags are displayed for selection.

提示 Output via the X122, X132 or X142 interface Also use the "Output by digital output module" setting in the following cases: - The output occurs at the X142 interface by a DQ instead of a Timer DQ. - The output occurs by a digital output of the X122 or X132 interface (configured ** 39x required) In both cases you must define a PLC tag for the respective I/O address.




Output deactivated
When output is deactivated, the cam track is evaluated only in the software.

Extended parameters > Activation time


圖片: Activation time

The specified output cam type is indicated at the top of the Activation time configuration window.

For a time shift of the switch-on and switch-off times of the output cams, enter an activation time and a deactivation time.

Extended parameters Parameter > Hysteresis


圖片: Hysteresis

To prevent unwanted changes in the switching state of the output cams of a cam track, enter a hysteresis value.

When using output cams that reference the actual position, it is advisable to enter a hysteresis value (> 0.0).

Cam track technology object

In addition to the output cam technology object already described, the cam track technology object is also available.


上海騰希電氣技術有限公司專注于西門子PLC,V90伺服,V20變頻器等, 歡迎致電 13681875601

• 詞條

  詞條說明

• 組態* 2 層功能 生成樹 LLDP

  LLDP識別網絡拓?fù)銲EEE 802.AB 標準中定義了 LLDP（Link Layer Discovery Protocol，鏈路層發現協議）。LLDP 是一種用來發現網絡拓?fù)涞姆椒?。網絡組件使用 LLDP 與其相鄰設備交換信息。支持 LLDP 的網絡組件具有 LLDP 代理。LLDP 代理會定期發送與其自身有關的信息，并從所連接設備接收信息。接收到的信息存儲在 MIB 中。應用PROFINET

• 移植選項概述

  移植選項概述移植路徑如果要在較新版本的 TIA Portal 和 S7-1500 中使用現有項目或程序，可采用各種不同方式進行項目移植。下圖簡要描述一種移植方式：將項目移植到 TIA Portal 中通過“移植項目”(Migrate project) 功能，可移植在 TIA Portal 系統之外由 STEP 7、WinCC、WinCC flexible 或 SINUMERIK 創建的項目。項目移

• 移動 CP 的喚醒

  移動 CP 的喚醒通過“授權電話號碼”喚醒的權限僅當根據電話號碼對發送通信伙伴進行授權的情況下，CP 才會接受喚醒 SMS 或喚醒呼叫。在 STEP 7 中的“授權電話號碼”列表中為 CP 組態這些電話號碼。提示STEP 7 項目中的“授權電話號碼”此處輸入的電話號碼可使傳輸此電話號碼的發送方有權觸發連接建立請求。如果在列表中輸入星號 (*)，CP 將接受所有發送方發來的 SMS 消息。如果列表為

• 組態 ET 200S

  組態 ET 200S簡介ET?200S 系列的 DP 從站和 I/O 設備的組態方法與其它模塊化 DP 從站和 I/O 設備的組態方法相同。 ET?200S 的模塊位于硬件目錄的“分布式 I/O”中。組態 ET?200S 的插槽規則組態 ET?200S 時，以下規則適用：插入 ET?200S 模塊時，請不要留下任何間隙。插槽 1： 僅用于 PM-E